How much does gutter installation cost in Kent, WA?

Last Updated: October 23, 2026

The short answer, and what it leaves out

Gutters of Kent installs seamless gutters across Kent and South King County, and the first question is nearly always the price. For 5-inch seamless aluminum gutters, installed, plan on a typical Seattle-area range of about $8 to $13 per linear foot. That number covers the gutter runs formed to length on site, hung and pitched toward the outlets. Downspouts, removal of the old system, guards and any fascia repair are separate lines, and Washington sales tax applies on top of the whole thing.

The per-foot figure is a starting point, not a total. A single-story house on a flat valley lot and a two-story house with several inside corners and a buried downspout line can share the same footage and price quite differently. The work is done by licensed and insured contractors, and the gutter cost estimator gives a budgeting number without a phone call.

Typical price ranges for gutter work around Kent

These are budgeting ranges, not Gutters of Kent’s rates and not a quote; the final number comes from measuring the house. Local ranges are labeled Seattle-area, and national figures are labeled national.

Downspouts are counted, not measured, and the count follows the roof area draining to each run. The guide to how many downspouts a house needs explains that sizing, and the downspouts page covers the work itself. The two guard tiers are different products, which the gutter guard cost guide separates. No guard makes a gutter maintenance-free.

What gutter replacement adds to the cost

Replacement is the install price plus the removal line, which typically adds about $150 to $325 to a Seattle-area job. The bigger unknown is the fascia, which is seen properly for the first time when the old run comes off. If it is soft or split, new hangers will pull out of it, and it has to be repaired before anything is hung. That repair is a separate scope with no published figure, and the gutter and fascia repair page explains how it is assessed.

Kent’s housing stock gives a reason to budget for that look. Census figures (ACS) put Kent’s median year built at 1985, with 38.5% of homes built before 1980, and King County Assessor records give ZIP 98032, which covers much of the valley and West Hill, a median build year of 1967. Age is context, not proof of rot, but an estimate on an older house should say what happens if the board behind the gutter is bad. The gutter replacement page covers the full scope, and repair vs replacement helps decide whether a full system is even the right call. If a roof is due soon, read whether to replace gutters with a new roof first, because the gutters come off for the roofers anyway.

What moves a Kent gutter price up or down

Within the per-foot range, the house decides where a job lands. None of these drivers is a fixed surcharge; each changes the time, material or risk in the job.

Rain shapes the scope more than the per-foot price. The NOAA Kent station averages 40.09 inches a year, with November averaging 6.23 inches against 0.67 in July, so downspout discharge gets as much attention as the gutter. A well-priced gutter that dumps water at the foundation is still a problem. Where downspouts should drain covers the options.

What’s inside a Kent gutter price

An estimate bundles costs that rarely appear as separate lines. Where no public figure exists, the part is listed as scope to check.

Why labor costs more around Kent

The wage gap explains much of the regional premium. O*NET, the U.S. Department of Labor’s occupation database, lists rain gutter and downspout installation among the tasks of sheet metal workers. According to the U.S. Bureau of Labor Statistics, in the Seattle-Tacoma-Bellevue area that occupation earns a mean $52.21 an hour against a national mean of $32.62, about 60% higher; the medians are $52.80 and $29.71. Two cautions apply. The Seattle category also includes HVAC duct and commercial sheet metal work, so it is not a gutter-installer wage; roofers, a nearby trade, earn a mean $35.21 locally against $27.95 nationally. And a wage is not a billing rate. The billed rate also carries insurance, L&I registration and bond, vehicles, ladders and staging, a seamless gutter machine, and overhead, which is why no one should multiply a wage by hours and call it a price.

Why metal prices matter, and how much

The BLS producer price index for aluminum mill shapes is up about 25% over the latest 12 months, and copper and brass mill shapes about 30%. These are national producer indexes, not retail gutter prices, and metal is only part of an installed foot, so the estimate does not rise by the same share. It does explain why an older price may not hold. The post on aluminum prices and gutter costs goes further.

Permits, fees and incentives in Kent

Kent City Code 7.05.070 requires a permit for work that constructs, installs or modifies any storm or surface water drainage structure or facility in the city, so a job that changes a buried downspout connection is storm drainage work, not just gutter work. The King County Surface Water Design Manual, which Kent adopts with its own changes, requires a perforated pipe connection for any roof downspout tied into the local drainage system. Under Kent City Code 7.04.180, roof runoff may not go to the sanitary sewer unless the city expressly authorizes it. For gutter replacement that discharges at the surface, check with the City of Kent Permit Center for the current rule before work starts.

There is no permit fee table here because no Kent fee figure for this work could be confirmed; any fee comes from the city at the time of the permit. The underground downspout drains guide explains what a buried connection involves.

No rebate or incentive for gutters or downspouts was found for Kent; the RainWise program covers eligible Seattle neighborhoods only.

An illustrative example: what 150 feet works out to

For illustration, assume a house with 150 linear feet of roof edge getting 5-inch seamless aluminum. At a typical Seattle-area range of about $8 to $13 per linear foot, the gutter runs alone work out to about $1,200 to $1,950. That figure leaves out downspouts, removal of old gutters, guards, fascia repair and any buried connection, and Washington sales tax (10.4% at most Kent addresses) applies to the whole contract once those are added.

This is arithmetic on a published range with an assumed footage: not a quote, not a typical Kent total and not a Gutters of Kent price.

Repairs, half-round, box and commercial: why there is no single number

Some work does not fit a per-foot band. Gutter repair is priced by what failed and where: resealing one single-story miter and re-hanging a sagging second-story run on soft fascia are very different jobs. The sagging gutter repair page explains why a sag is often a fascia problem first.

Copper gutters and half-round profiles cost more because of the metal, the hangers and the soldered or detailed joints. Box gutters and commercial gutters depend on the trough, how it is built into the roof, the area it drains and access, so they are priced from a site visit.

How to compare two gutter estimates

A lower per-foot number is only lower if it buys the same work. Check each estimate for:

• Gutter size, profile, gauge, and hanger type and spacing
• Number of downspouts, their size and where each one discharges
• Whether removal and haul-away of the old system is included
• What happens if the fascia behind the old gutter is soft
• Any buried connection, and who handles the permit
• Whether sales tax is shown or already in the total

Seamless gutters still have joints at corners, end caps and outlets, so ask how those are sealed. The contractor’s registration, bond and insurance can be checked with L&I’s Verify a Contractor tool; the guide to checking a gutter contractor in Washington walks through it.

Getting a number for your own house

Start with the gutter cost estimator: enter linear feet, stories, material, downspouts, removal and guards for a budgeting range. For a real number, the walk-around measures each roof edge, checks the fascia and drip edge, and traces where every downspout lets go, so the estimate reflects the house rather than an average. Whether the home sits on the Kent valley floor or up on East Hill, the same measurements set the price. When you are ready, Get an Estimate and include the address and a few photos of the roof edge.